<
DOWNLOAD TUB OPERATION PDF
OPERATING INSTRUCTIONS | DISPLAY
MESSAGES | TROUBLESHOOTING |
ADDING CHEMICALS
OPERATING
INSTRUCTIONS
INITIAL START-UP
When your spa is first actuated, it will go into Priming
Mode, indicated by "Pr." The Priming Mode
will last for less than 5 minutes and then the spa
will begin to heat and maintain the water temperature
in the Standard Mode.
TEMPERATURE ADJUSTMENT
(80 – 104 F)
Press the TEMP button to display the temperature previously
set. The set temperature is flashed on the display.
In a few seconds, the numbers will stop flashing,
and the display will show the actual water temperature.
Pressing the pad a second time will cause the set
temperature to increase or decrease depending on what
direction was last chosen. Each press to follow will
change the set temperature in the same direction.
If the opposite direction is desired, release the
pad and let the display revert to the actual water
temperature. Press the pad to display the set temperature,
and again to make the temperature change in the desired
direction. After releasing the pad, in 3 seconds the
LCD will show the actual water temperature.
JETS
Press the JETS button to turn on the low speed of
the pump. Press the pad again to turn on the high
speed of the pump. If left running the low speed will
turn off after 4 hours: the high speed will turn off
after 15 minutes on models with the exterior indicator
lights and 30 minutes for the other model of hot tub.
Please note that the heater is not engaged when the
high speed of the pump is in use. If the tub has cooled
off too far, use only the low speed to engage the
heater.
LIGHT
Press the "Light": button to turn the light
on and off. If the light is left on, it will automatically
shut off after 4 hours.
MODE
The default mode is set to Standard ("St"
symbol on the display). To change the mode press the
"Temp" button then the "Light"
button before the LCD stops flashing. If any mode
but "St" is showing (Ec or Pr) proceed through
the modes until the "St" symbol comes onto
the screen. The mode will be displayed only briefly
when you get power to the hot tub.
PRESET FILTER CYCLES
Your Hot tub will automatically filter itself twice
a day. The first cycle will start one minute after
the tub is powered up, the second, 12 hours after
that. The filter cycle is 2 hours in duration.
DISPLAY
MESSAGES
NO MESSAGE ON DISPLAY
Power has been cut to the hot tub.
HH "OVERHEAT" (Spa is shut down)
DO NOT ENTER THE WATER.
PLEASE CALL TRAVELLIN’ TUBS IMMEDIATELY
(416-887-9400). One of the sensors has detected
water at 118F.
OH "OVERHEAT PROTECTION" (Spa is
shut down)
DO NOT ENTER THE WATER.
PLEASE CALL TRAVELLIN’ TUBS IMMEDIATELY
(416-887-9400). One of the hot tub sensors
has detected a water temperature of 110 F.
IC "ICE"
Potential freeze conditions detected. Pump will automatically
activate regardless of hot tub status.
SA (Spa is shut down).
The sensor that is plugged into the Sensor "A"
jack is not working.
PLEASE CALL TRAVELLIN’ TUBS (416-887-9400) if
the message remains.
Sb (Spa is shut down)
The sensor that is plugged into the Sensor "B"
jack is not working.
PLEASE CALL TRAVELLIN’ TUBS (416-887-9400) if
the message remains.
Sn
Sensors are out of balance. If alternating with spa
temperature, it may just be a temporary condition.
If flashing by itself, spa is shut down.
PLEASE CALL TRAVELLIN’ TUBS (416-887-9400).
HL
A significant difference between temperature sensors
has been detected.
Indicative of a flow problem. Check water level in
the hot tub. If the water level is less than 2 inches
over the filter skimmer, add water up to at least
this level. If the problem persists,
PLEASE CALL TRAVELLIN’ TUBS (416-887-9400).
LF
Persistent low flow problems. Heater is shut down
but rest of spa functions continue to run normally.
Follow directions for HL above. Press any button to
reset the heater once the tub is full enough. If the
problem persists, PLEASE CALL
TRAVELLIN’ TUBS (416-887-9400).
dr
Possible inadequate water, poor flow, or air bubbles
were detected at the heater. Spa is shut down for
15 minutes. Ensure water level is at least 2 inches
above the filter skimmer. Press any button to reset
the system once the water level has been raised. If
problem persists,
PLEASE CALL TRAVELLIN’ TUBS (416-887-9400).
dY
Inadequate water detected in heater. Spa is shut down.
Follow directions for "dr" above. If problem
persists, PLEASE CALL TRAVELLIN’
TUBS (416-887-9400).
TROUBLESHOOTING
TUB HAS NO POWER
Check your fuse box or breaker panel to ensure that
the fuse is not blown or the breaker tripped.
N.B: If your hot tub
loses power for any reason (plug pulled, breaker tripped,
etc.) you will have to press the RESET button on the
GFI plug (yellow wall plug attached to hot tub) to
start it again. This is a safety switch to avoid electrocution
by holding the plug with wet hands.
PUMP WILL RUN BUT THERE IS NO WATER FLOW
Make sure the filter is clean.
Make sure the suction intakes are free of debris.
Make sure the water level is at least 2" above
the skimmer filter.
Check to ensure that all adjustable flow jets are
turned open.
PUMP RUNS AND THERE IS WATER FLOW BUT NO
HEAT
Follow the directions above to increase the temperature.
DO NOT expect to feel hot water coming from the jets.
Make sure all valves are open to allow full water
flow through the system. Limited water flow will NOT
build enough pressure to allow the heater to come
on.
Clean the filter to allow maximum water flow.
PULSATING OR MINIMAL WATER FLOW IN HIGH SPEED
MODE
Make sure water level of the hot tub is at least 2"
above the filter skimmer.
Ensure that all jets are turned fully open.
Make sure the suction intake covers are free of debris.
BLOWER WILL NOT BLOW AIR INTO THE HOT TUB
Make sure the dial-controls are set to the "open"
position
ADDING
CHEMICALS
CHLORINE
You must add the chlorine that we have provided (i.e.
if the hot tub is dropped off on Thursday night, you
would add them Friday, Sunday, Tuesday) these have
been pre-measured for you. Please add the full contents
of the baggie to the hot tub with the jets running
on high and the air vents open. Allow the hot tub
to finish one cycle on high (15 minutes) and then
you are ready to use the hot tub. Do not add more
or less than the prescribed amount at any one time.
Variance from the schedule may result in your tub
having too much or too little chlorine in it at any
time and this could result in bacterial growth, or
a chemical burn.
FOAM AWAY
Add the Foam Away 5-6 drops at a time with the jets
running on high if the tub has developed excessive
foam on the surface after heavy use.
SPA PERFECT
You will only receive Spa Perfect if you are renting
the hot tub for an extended period of time. You will
add one cap full (100ml) once a week to keep the spa
crystal clear and odour free.
If you have any questions about
the addition of any chemical to your hot tub please
call Travellin’ Tubs before you proceed with
the addition. 416-887-9400 |
